内装式空射运载火箭重力出舱机箭耦合动力学分析

研究了以运输机为平台的内装式运载火箭空射过程载机和火箭的耦合动力学建模。建模针对两个阶段：第一阶段，火箭固定于载机机舱内，两者构成一个整体，按照普通刚体的力学方法处理；第二阶段，火箭解锁后，沿着舱内的发射筒向外滑行，载机和火箭形成两刚体相互作用的耦合系统，基于牛顿-欧拉法建立系统动力学模型。载机在空射火箭过程中，油门和升降舵满偏，在加速前飞的同时拉大姿态俯仰角，火箭在自身重力分量和惯性力的作用下，沿着机舱内的发射筒加速向外滑行，直至与载机分离。数值仿真分析了空射过程载机的重要力学参数的变化过程，验证了载机操控策略的可行性和安全性，可为未来中国空射运载火箭技术设计提供数据参考。     

复杂动态环境下无人飞行器动态避障近似最优轨迹规划

针对复杂动态环境下无人飞行器的动态障碍规避问题，基于合理假设建立了无人飞行器和动态障碍的运动学模型，并综合考虑无人飞行器飞行过程中的终端约束、控制输入约束、安全避障约束等，以能量最少为性能指标构建动态避障问题数学描述。之后，针对终端约束和控制输入约束，依据优化模型预测静态规划算法(OMPSP)生成初始轨迹；针对动态避障问题的不等式约束，引入松弛变量并结合滑模变结构控制方法设计松弛变量动力学，实现对一个、多个或同时多个动态障碍的安全规避；最后，依据有限时间微分动态规划(RHDDP)算法进行轨迹优化，获得满足上述各种约束并能规避动态障碍的近似最优轨迹。     

Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

散射对高温气体-碳黑颗粒混合物辐射传输的影响

基于全光谱k分布(Full spectrum k distribution,FSK)模型、MIE理论和有限体积法(Finite volume method,FVM),构建了均温、均质辐射参与性气体-碳黑颗粒混合物介质热辐射传输模型,并分析了碳黑不同尺寸、不同体积浓度以及介质不同路径长度和不同温度条件下,因忽略碳黑颗粒散射所导致的介质热辐射传输特性(如辐射热流、辐射源项)的计算误差。研究结果表明:体积分数不变,增大粒径,计算误差呈现出先增大后减小的趋势;数密度不变,增大粒径,或者粒径不变,增大体积分数,均将使得计算误差相应增大;粒径、体积分数不变,增大路径长度,或者升高介质温度,均将增大计算误差。通常对于含有大颗粒、高碳黑浓度的辐射参与性气体-碳黑颗粒混合物介质,碳黑颗粒散射不能忽略。     

Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

一种基于VPL 的元器件快速建模方法

为了更好地落实航空电子模块的可制造性设计审查工作,结合航空电子模块产品特点和技术要求,建设了基于Valor软件的PCB/PCBA设计与检测自动化分析系统.元器件模型库作为该系统的必要组成部分,其覆盖范围和数据精度对审查结果至关重要.本文将从元器件模型库建设必要性、建设过程和建模工艺要求三个方面进行阐述,并提出一种基于Valor VPL的元器件快速建模方法,应用结果表明,该方法能够高效构建满足系统审查精度的元器件模型,使大规模元器件模型库的建设成为可能.     

Development and performance evaluation of tropospheric scintillation model on Ku-band satellite link over Akure,Nigeria

Existing amplitude scintillation prediction models often perform less satisfactorily when deployed outside the regions where they were formulated. This necessitates the need to evaluate the performance of scintillation models developed in one region using data data from other regions while documenting their relative errors. Due to its variation with elevation angle, frequency, other link parameters and meteorological factors, we employed three years (January 2016 to December 2018) of concurrently measured satellite radio beacons and tropospheric weather parameters to develop a location-based amplitude scintillation prediction model over the Earth-space path of Akure (7.17^oN, 5.18^oE), South-western Nigeria. The satellite beacon measurement used Tektronix Y400 NetTek Analyzer at 1 s integration time while meteorological parameters, namely; temperature, pressure and relative humidity were measured using Davis Vantage Vue weather station at 1 min integration time. Comparative study of the model’s performance with nine (9) existing scintillation prediction models indicates that the best and worst performing models, in terms of root mean square error (RMSE), are the Statistical Temperature and Refractivity (STN) and direct physical and statistical prediction (DPSP) models with values 11.48 and 51.03 respectively. Also, worst month analysis indicates that April, with respective enhancement and fade values of 0.88 and 0.90 dB for 0.01% exceedance, is the overall worst calendar month for amplitude scintillation.     

抗辐照通用扩展SiP芯片设计

研究微小卫星综合电子系统的SiP技术实现方法。首先介绍微小卫星综合电子系统结构的组成和采用SiP技术的必要性，然后对综合电子系统进行功能模块划分，并对其通用扩展模块进行详细的SiP设计，包括抗辐照器件选型、原型验证、SiP原理图、基板管壳一体化设计、建模仿真、制造加工、实装测试验证等，通过SiP技术实现了一种星载综合电子系统中通用扩展SiP芯片产品，经过实际验证测试，在保证模块功能和性能的前提下，整体模块重量从230 g减轻到48 g，体积由180 mm?130 mm?17 mm减小到46 mm?46 mm?8 mm，很好地满足了星载功能模块小型化、轻量化设计需求。     

联邦学习安全与隐私保护综述

联邦学习是一种新型的分布式学习框架，它允许在多个参与者之间共享训练数据而不会泄露其数据隐私。但是这种新颖的学习机制仍然可能受到来自各种攻击者的前所未有的安全和隐私威胁。本文主要探讨联邦学习在安全和隐私方面面临的挑战。首先，本文介绍了联邦学习的基本概念和威胁模型，有助于理解其面临的攻击。其次，本文总结了由内部恶意实体发起的3种攻击类型，同时分析了联邦学习体系结构的安全漏洞和隐私漏洞。然后从差分隐私、同态密码系统和安全多方聚合等方面研究了目前最先进的防御方案。最后通过对这些解决方案的总结和比较，进一步讨论了该领域未来的发展方向。